Ruptela - Installation Guide > 자유게시판

Installing a GPS tracking device in your automobile isn't a complicated task, however it is important to take safety precautions, as such the set up should solely be carried out by a professional Auto Electrician. Usually, it takes approximately 2 hours to set it up depending on the complexity of the vehicle’s wiring construction. GPS device installation (basic installation with no gasoline/temperature/door sensors related), learn the following instructions. Read extra on the Do’s & Dont’s of GPS machine set up at the end of this document. Screwdriver set, Plier, Multimeter and Wire Stripper/Cutter/Crimper. Before putting in the system, you need to notice down International Mobile Equipment Identity (IMEI) variety of the GPS tracking device and the SIM GSM quantity. Then insert the GPRS enabled SIM card to the device. You could as properly obtain the vehicle addition template to report vehicle data. Then insert the GPRS enabled SIM card to the machine.

It's possible you'll as properly download the vehicle addition template to file automobile data. IMEI is a novel quantity to determine GSM, WCDMA, iTagPro tracker and iDEN cell phones, satellite tv for pc telephones, in addition to some telematics units that works as a singular identification code. This 15-digit quantity is usually printed either on the bottom of the GPS monitoring unit or the system case; you require IMEI to register the GPS tracking device on the fleet management software. Red wire (of GPS system) to 1 end and the facility source of the vehicle to the other finish of a 1Amp fuse. Secure the fuse to the instrument chord with a cable tie. Connect Black wire (-ve) on the harness to Chassis Ground (any bolt or wire with -ve power). Connect Yellow ignition sense wire to the vehicle’s ignition source to assist observe ignition ON/OFF events. Please seek the advice of the automobile wiring diagram to find the ignition wire.

You possibly can verify the car ignition wire by measuring the vehicle’s working voltage while the engine is running. Once recognized, connect the ignition wire to the FUSE Box with a 3M Scotchlok so that it's going to snap into place and can get it correctly seated. Please seek advice from the connection diagram beneath, for a detailed view of the wires & connectivities. One of many quickest and the very best place to mount a GPS tracking device or itagpro tracker a GPS tracker is underneath the dashboard or an exterior iTagPro smart tracker location in a horizontal position with a clear view of the sky. It's possible you'll experiment with putting the tracking device at totally different areas on the vehicle to determine the most effective reception for the specified stage of concealment. If the device has exterior iTagPro tracker GPS antenna then place the antenna underneath the dashboard or wherever handy utilizing double-sided sticky-tape to ensure it’s firmly fastened there. Once you’ve placed the GPS itagpro tracker within the automobile, you’re all set.

Connect the wire socket and GPS/GSM antenna (of these with external antenna) to the GPS machine. As quickly as the gadget is powered on, itagpro locator both inexperienced LEDs (GPS & communication) will flash on and off while trying to find indicators. When full signal energy is achieved, each LEDs will constantly illuminate. With the intention to validate performance, we have to ring the GSM mobile number of the SIM. If it rings or responds with a busy be aware, you may safely assume that the machine is functioning correctly. If there is no response, you may need to re-insert the SIM card and check the wiring once more. Please Log into the platform with your credentials to ensure the machine communicates with the server. Note: Be sure that the IMEI no’s & cell no’s you up to date against the vehicles are appropriate. To avoid mishaps while set up, be certain the car ignition is turned off before initiating wire connections. It is always advisable to disconnect the suitable jumpers /connections of vehicle’s energy supply during the GPS machine installation; that is to keep away from quick circuits and wiring damages.

Be certain the wires stay disconnected while mounting/dismounting the machine. Secure all wiring with Scotchlok, cable connectors, and electrical insulation tapes. Never enable any naked wiring to stay exposed; connections should be least seen. Ensure further insulation if wires go through a visible/exterior region, in order to keep away from brief circuit/wiring damages. GPS monitoring units could be mounted in a zone of limited access, so none has direct entry to the instrument. Keep connecting wires as discreetly as attainable, making it much less seen and iTagPro tracker hard to notice. For the safety of personnel, machine & vehicle, keep away from connecting system wires to the board computers (ECU) or iTagPro tracker management models. Ensure that you fasten wires to different wires/non-transferring components and iTagPro tracker not to fasten near heat emitting and ItagPro moving objects as friction/heat emission could cause sparks leading to short circuits. While connecting ignition wire verify if it’s the real ignition wire (energy supply out there solely when the ignition is on). Using a multimeter, iTagPro features check energy circulate by turning on/off the engine.